Emissions Measurement Company COLORADO , United States
Since May, 2015
EMCo clients can be confident in our experienced test crews and, in most cases, have a final test report within fifteen business days of the completion of the test. We believe in maintaining a clear line of communication with the client from the inception of the testing project to its completion, and our staff is always available to address any questions or concerns that may arise. We provide on-site preliminary testing results to our clients at the completion of each testing program, and send final results within a few business days. All testing reports are produced by a former state regulator. Draft testing reports are usually available within ten business days of test completion. EMCo is fully compliant with ASTM D7036-04, and our Project Managers maintain QSTI certification.
Our testing capabilities include EPA Reference Method testing for the following constituents:
- Nitrogen Oxides (Methods 7E & 20)
- Carbon Monoxide (Method 10 )
- Total Hydrocarbons (Method 25A)
- Sulfur Dioxide (Method 6C)
- Particulate Matter (Methods 5, 5B, 5F, 17), including PM10 (Method 201a) and Condensable Particulate Matter (Method 202)
- Formaldehyde (Methods TO-11a, 323, or CARB 430)
- Opacity (Methods 9 & 22)
- Hazardous Air Pollutants and Non-Methane/Ethane Organic Compounds (Method 18)
- Mercury (Method 30B)
Note that this list is not all-inclusive; please contact us to design a testing program to fit your specific needs.
Emissions Measurement Company (EMCo) was established to provide high-quality source emissions testing services to industrial clients. Our principals have over 30 years of combined experience in source emissions testing, having completed hundreds of testing campaigns throughout the United States with clients in various industries. Our goal is to offer the most experienced field staff and rapid data turnaround in the testing industry at highly competitive prices.
While EMCo caters to clients from various industries, we provide specialized experience in two focus areas: Oil and Gas Production and Transmission and Electric Power Generation.
Oil and Gas Production and Transmission
EMCo specializes in oil field engine and turbine compliance testing. Our fully self-contained testing vehicle is capable of rapid mobilization - usually within 24 hours’ notice - and has the ability to begin reference method testing within minutes of arriving on-site, eliminating costly setup time. We understand how important it is for our clients to minimize the number of field hours involved with testing; paying overtime to field personnel and adjusting unit loads can create significant financial and logistical inconveniences. Considering this, we have developed our test vehicle with efficiency and mobility in mind. We have the ability to efficiently test multiple units in a single day. EMCo will cater to any client needs, whether it is on-site formaldehyde analysis or providing a man-lift for stack access. EMCo also offers (and recommends) pre-test site visits to inspect testing locations and assist in avoiding costly downtime for stack modifications. Our testing capabilities include tailored testing programs for the following federal regulations:
- NSPS Subpart JJJJ – Stationary Spark Ignition Internal Combustion Engines
- NSPS Subparts GG and KKKK – Stationary Combustion Turbines
- MACT Subpart ZZZZ – HAPs from Stationary Reciprocating Internal Combustion Engines
Other industry services include:
- Fuel gas sulfur content analysis
- Turbine mapping and diagnostic testing
Power Generation
EMCo takes a service-minded approach to our industrial clients. Understanding load demands and the need for a flexible testing company, we offer efficient testing services for reduced load conditions and multiple load testing. All project managers at EMCo have at least 8 years of experience working with power generation clients. Our state-of-the-art testing trailer offers a temperature- controlled environment for our gas analyzers and acts as a mobile laboratory for performing on-site PM and Hg analysis. EMCo realizes the importance of data accuracy and repeatability. All projects are conducted by highly experienced and qualified testers. We are always willing to take the extra time to provide accurate on-site numbers, so any potential data issues can be identified and corrected before we leave your site. All testing reports are produced by a former Colorado Air Division CEMS Coordinator. Our testing capabilities include the following:
- Particulate matter testing
- Straight extractive and dilution system testing
- Exhaust flow measurements via Methods 2, 2F and 2G
- 40 CFR Part 60 and 75 RATAs
- Mercury RATAs
| Company Name | Emissions Measurement Company |
| Business Category | |
| Address | COLORADO United States |
| President | NA |
| Year Established | NA |
| Employees | NA |
| Memberships | NA |
| Hours of Operation | NA |
- Power Generation